Please Choose:
 

Our Promise To You, Guaranteed Peace of Mind

Warranty
Northwest Railing is a distributor for Railcraft.  Railcraft® is a leading manufacturer of powder coated, aluminum glass and picket railing systems for residential and commercial markets.  Railcraft® has been designing and manufacturing aluminum railing systems since 1985.  Our dedicated approach to development, research, and engineering enables us to provide our customers with the highest level of quality and versatility possible.

All Railcraft® railing systems are engineered to achieve ultimate strength while providing a system that is aesthetically pleasing.

With the use of high strength alloys, we can effectively replace wood, composite, vinyl and steel products with weather resistant, powder coated aluminum.

All of our systems come with a limited 20-year residential warranty as well as site-specific commercial warranties.

Railcraft® products can span up to 96" between posts on picket systems and up to 66" between posts on glass systems.  Railcraft® meets all North American building code requirements.

Railcraft® products have been used successfully in thousands of projects throughout North America.  At Railcraft®, we understand that today's consumer is looking for reliable, low maintenance products with design flair that are practical AND architecturally pleasing.

Care and Maintenance
Clean the aluminum components of the railing with warm soapy water using a sponge or soft cloth. Do not use abrasive cleaners that may scratch the railing. For stubborn stains consult your Northwest Railing representative.

Matching touch-up paint is also available by consulting your Northwest Railing representative.

If the product is installed within one (1) mile of a coastline, saltwater bay, or any area prone to saltwater spray, there are additional and specific maintenance requirements within the installation, care, and maintenance instructions, which apply. If the product is installed within one (1) mile of a coastline, saltwater bay, or any area prone to saltwater spray, Northwest Railing will have no obligations under this warranty unless the original owner signs and returns the attached warranty registration card to the dealer/distributor or manufacturer.

Northwest Railing and Railco Aluminum Railing Systems will require cleaning and caring for the exterior aluminum surfaces. Annual inspections are sufficient for most areas, however coastal areas have special requirements.

Coastline Maintenance Requirements
The salt and moisture in the air of such regions can create a damaging build up of salt on the railing components. This damaging build-up requires monthly inspections of all railing components to detect and subsequently remove the harmful residue.

Upon detection of any salty build-up, monthly cleaning of the aluminum surface is required to regain the product's original look, quality and luster and to maintain its warranty eligibility.

Product Cleaning
For light cleaning, rinse with water from bottom to top and back to bottom. This will clean the surface on the way up and prevent the collection of dirty “run down” and possible streaking. Air dry or wipe dry with a soft, dry, lint-free cloth.

If light cleaning does not clean the debris, rinse the surface with clean water from top to bottom. Use a sponge and clean with mild soap and water. Immediately rinse any “run down” to lower parts of the building. Do not allow cleaning solutions to collect or “puddle” on surfaces. Immediately rinse with clean water. It is very important that cleaning solution does not dry on the surface. Air or wipe dry with a soft, dry cloth. For stubborn, water-soluble debris, repeat steps above until clean.

For a protective wax finish, apply a quality brand of car wax to the aluminum surface (follow wax manufacturer's application instructions)

For optimal cleaning, do not clean coated aluminum surfaces in direct sunlight or in temperatures too hot or too cold. Do not use abrasive cleaners that may scratch the cladding and avoid excessive rubbing or over-cleaning.

Recommended Maintenance Schedule
Aluminum handrails and guardrails are intended to provide both safety and aesthetics for the life of the structure to which they are affixed. Ensuring fulfillment of these functions depends, to a large extent, on following some basic maintenance procedures.

Northwest Railing Aluminum Railing Systems recommends that the following actions be undertaken:

1.Railing should be hand washed with mild detergent and rinsed with clean water as needed.

2.All screws should be checked every year for snugness. Caulking should be removed and replaced if showing signs of deterioration. If screws require replacing, replace them with appropriate fasteners.

3.Guardrails fastened to concrete decks should be inspected carefully on an annual basis at each plate for evidence of moisture leakage or loose connections.

Any evidence of these anomalies should be reported to your Northwest Railing representative for followups and discussion.

Your Privacy | Disclaimer | Terms of Use | Contact Us | Admin | Mail |
Another NukeWebDesign Site Hosted by City of Kenora.ca
Northwest Railing & Distributors Inc.
1493 Erin St., Winnipeg, Manitoba, R3E 2S9
Phone 204-632-1147
Fax 204-489-8683